Havis Shields Automobile Accessories C 3311 18 2 User Manual |
INSTALL INSTRUCTIONS C-3311-2 & C-3311-18-2
SLIDE-OUT TRUNK TRAY
2006-2008 CHEVROLET IMPALA
TOOLS REQUIRED:
7/16” wrench
Powered drill w/ 3/16” drill bit
Ratcheting wrench
Standard socket set
Screwdriver set
HARDWARE:
QTY DESCRIPTION
PART #
12
16
12
4
4
4
2
1
1
4
¼-20 x ¾” Hex head bolts
¼” Flat washers
¼-20 Serrated nuts
8-32 x 3/8” Machine Screws
8-32 Keps Nuts
¼” x ¾” Hex head lag bolts (only on C-3311-18-2)
Front Mounting Leg
Rear Driver-side bracket
Rear Passenger-side bracket
Mounting plate w/ pem ¼” pem studs (Use 2 on C-3311-18-2)
P.S. Front Mounting Bracket (only on C-3311-18-2)
P.S. Rear Mounting Adapter Bracket (only on C-3311-18-2)
GSM33001
GSM31005
GSM30023
GSM33540
GSM30027
GSM33060-1
CM001390
CM001391
CM001392
CM001393
CM001394
CM93712
1
1
Always!
ꢀ Read all instructions before installing any Havis-Shields Equipment Corp products.
ꢀ Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes!
ꢀ Use hardware provided with install kit
ꢀ For product support, visit the Install Instructions Section of our website at
SUB ASSEMBLY: (Use Iso views on page #1 & 2 for sub assemblies)
- 1 -
1. Attach forward mounting legs to the slide out tray.
• Attach forward mounting legs with provided 8-32 screws and hex nuts to slide track.
• The front legs will be square to the slide tray.
•
On the front passenger side of the half tray, passenger side front mounting brackets
(CM001394) will attach to the front mounting legs.
2. Attach rear-mounting brackets to the slide out tray.
•
Loosely attached the rear mounting brackets to the “Cradle Bracket” using ¼” x ¾”
hex head bolts, washers and serrated nuts.
•
On the rear passenger side of the half tray, passenger side rear mounting adapter
bracket (CM93712) will attach to the rear mounting brackets.
INSTALLATION:
1. Mount slide tray in vehicle trunk.
• Slide trunk tray into vehicle with the tall front mounting legs in first. Prop up tray in
position using block of wood.
• Once you have the tray square, and pushed to the forward most position in trunk,
attach mounting brackets to vehicle using the supplied mounting plates.
• On the half tray, passenger side, you will bolt the passenger side front mounting
brackets (CM001394) to the vehicle using ¼” x ¾” Hex head lag bolts. (Pre-drill w/
3/16” drill bit)
• Position mounting plates into locations shown in photos #1 and 2.
• Loosely attach front and rear mounting brackets to mounting plates using ¼” serrated
nuts.
• On the passenger side, attach passenger side rear mounting adapter brackets
(CM93712) to vehicle using ¼” x ¾” hex head lag bolts. (Pre-drill w/ 3/16” drill bit)
Forward Mounting Brackets
Rear mounting brackets
Mounting
Plate
Mounting
Plate
- 3 -
C-3311-2^3311-18-2_INST_9-07
• Tighten all loose hardware.
• Be sure tray slides smoothly and locks in the closed position. If the tray does not slide
smooth then most likely the tray is not square or level.
#8 screws &
hex nuts
¼” bolts, washers,
& nuts
Photo #3
- 4 -
C-3311-2^3311-18-2_INST_9-07
|
Graco Baby Accessories ISPP066AA User Manual
Graco Building Set 3A0101C User Manual
Haier Microwave Oven MWM10100SS User Manual
Harbor Freight Tools Lathe 33684 User Manual
Hasbro Games GIJoe Cobra Liquidator ATF User Manual
Hasbro Motorized Toy Car 06605 06630 User Manual
Hasbro Robotics 85243 User Manual
Havis Shields Work Light CD FX HID 1 User Manual
Hotpoint Washer WMXTF 842 User Manual
Humminbird Fish Finder 1157C User Manual