HEAVY-DUTY WAGON WITH
WOOD SIDES
MODEL G7112
INSTRUCTION SHEET
COPYRIGHT © MARCH, 2004 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#6184 PRINTED IN CHINA
ASSEMBLY INSTRUCTIONS
WOOD STAKE SIDES & PULL HANDLE
1. Turn the wagon right side up.
2. Mount the left and right rear wood stake sides
to the outside of the bed with M6-1.0 x 45 slot
head screws, flat washers, and acorn nuts,
as shown in Figure 3.
FRONT SUPPORT ASSEMBLY
1. Attach the steering bracket to the front axle
assembly with the special bolt, 10mm flat
washer, and hex nut. Insert the cotter pin
through the hole of the special bolt, and
spread. Do not overtighten.
2. With the bed upside down, mount the steer-
ing bracket to the bed with four M6-1.0 flat
head screws, flat washers, lock washers,
and hex nuts. Figure 2 shows the steering
bracket preperly mounted to the bed.
Figure 3. Wood stake side mounted to the out-
side of the bed.
3. Mount the front wood stake side to the out-
side of the bed with M6-1.0 x 45 slot head
screws, flat washers, and acorn nuts.
4. Mount the rear wood stake side to the outside
of the bed with M6-1.0 x 45 slot head screws,
flat washers, and acorn nuts.
5. Using the M6-1.0 x 75 slot head screw, M6-
1.0 hex nut, flat washer, and lock washer,
attach the pull handle with the to the opening
in the front axle support.
Figure 2. Steering bracket and front axle assem-
bly mounted to the bed.
REAR AXLE ASSEMBLY & WHEELS
1. Loosely mount the rear axle support to the
bed using two M6-1.0 x 16 flat head screws,
flat washers, lock washers, and hex nuts.
2. Slide the rear axle braces onto the rear axles
and bolt the opposite ends of the braces to
the bed using the remaining M6-1.0 x 16 flat
head screws, flat washers, lock washers, and
hex nuts.
If you need additional help with this procedure,
call our service department at: (570) 546-9663.
3. Tighten the rear axle support.
4. Slide a wheel onto each axle with the valve
stems to the outside.
5. Insert and spread a cotter pin into each
axle, and place the plastic axle caps into the
axles.
G7112 Parts Breakdown and List
6
12
5
22
25
7
1
11
8
14
22
26
9
18
3
15
4
2
17
21
13
23
16
15
17
20
22
18
REF
1
PART#
DESCRIPTION
BED
REF
14
15
16
17
18
20
21
22
23
25
26
PART#
DESCRIPTION
P7112001
P7112002
P7112003
P7112004
P7112005
P7112006
P7112007
P7712008
P7112009
PFH38M
PS83M
P7112014
PN01M
SPECIAL BOLT M10-1.5 x 23
HEX NUT M6-1
2
PULL HANDLE
TIRES 4.10/3.50
PN02M
HEX NUT M10-1.5
3
P7112017
PLW03M
PW08M
PW04M
PW03M
P7112023
PN35M
COTTER PIN 3/32 x 1-1/2
LOCK WASHER 6MM
FLAT WASHER 16MM
FLAT WASHER 10MM
FLAT WASHER 6MM
PLASTIC AXLE CAP
ACORN NUT M6-1
4
FRONT AXLE ASSEMBLY
L/R WOOD STAKE SIDE
REAR WOOD STAKE SIDE
5
6
7
FRONT WOOD STAKE SIDE
REAR AXLE ASSEMBLY
REAR AXLE BRACE
8
9
11
12
13
FLAT HD SCR M6-1 x 16
PHLP HD SCR M6-1 x 45
PHLP HD SCR M6-1 x 75
P7112026
STEERING BRACKET
PS84M
|